Engineering economic analysis: Difference between revisions

From processdesign
Jump to navigation Jump to search
No edit summary
Line 1: Line 1:
==Measure of Economic Return==
==Introduction==
The following are "back of the envelope" type calculations for economic return of a project. These measures are quick and easy because they ignore some of the more complicated parts of evaluating a project including factors such as depreciation, time value of money and taxes.
===Payback Time===
The payback time is defined as the period of time (in years) required to break even on the initial economic investment. It is given by the equation:
<math>Payback time = Total investment/Average Annual Cash Flow</math>

This calculation is used to determine how quickly the project's fixed costs (i.e. land, machinery, etc.) can be recovered from the project.

===Return on Investment===


==Taxes==
==Taxes==

Revision as of 20:06, 23 February 2014

Measure of Economic Return

The following are "back of the envelope" type calculations for economic return of a project. These measures are quick and easy because they ignore some of the more complicated parts of evaluating a project including factors such as depreciation, time value of money and taxes.

Payback Time

The payback time is defined as the period of time (in years) required to break even on the initial economic investment. It is given by the equation:

This calculation is used to determine how quickly the project's fixed costs (i.e. land, machinery, etc.) can be recovered from the project.

Return on Investment

Taxes

Chemical production facilities are subject to the same financial levies by the government as all corporations. Specifically, corporations typically pay income taxes, and may collect incentives based on state and federal regulations. Detailed tax filings are almost always conducted by the accounting or financial department of a corporation. When preparing process economics estimations, taxes should be included, however all final cost estimates reported to management should be prepared by the appropriate specialist (Douglas, 23).

Corporate Taxes

The specific tax codes will vary from state to state, and from country to country (Peters, 303). The common factor will be that income is taxed at marginal rates. In the United States, this percentage is 35%, although the effective rate may be lower.

Corporate income taxes is a yearly expense. The percentage rate is to be applied on the income, not the revenue. See other Economics sections on the difference between income and revenue.

Investment Incentives

Local, state, and federal governments generally encourage capital investments by corporations. Financial incentives afforded to corporations include low interest loans, free capital for research and development, and tax holidays for new technologies.

When conducting economic estimates of a chemical process plant, especially if the plant utilizes efficient or "green" technology, it is important to investigate any and all sources of government incentives.

Depreciation

Depreciation, in the colloquial sense, is the loss of value of an item. As it pertains to the chemical process industry, depreciation is the loss of value due to "wear and tear" of the components and facilities of the plant. It is important to note that this does not include working capital or land.

Economics of Depreciation

Depreciation can be thought of as a yearly expense that the plant incurs. It can then be considered a cost, effectively reducing the income and thus the income tax. However, depreciation is not an actual cash flow. There is no transfer of money.

Note how depreciation lowers the amount of taxes:

where is the taxes due; is the gross profit; is the depreciation; and are the taxes due.

Two commons methods of calculating depreciation are discussed in the next sections.

Straight Line Depreciation

Straight line depreciation is the most common method of approximating depreciation when calculating profitability measures, such as return on investment (Seider, 392).

In this method, the depreciable value is written off over the total life of years at a constant linear rate:


, where is each year in the lifetime.


Therefore, the book value , or the initial cost of the item minus the accumulated depreciation charges, at year , can be defined as:


where is the initial cost of the item.

Depreciation Case Study

For example, let us find the book value after 3 years of a compressor which originally costs $50,000, has a depreciable value of $5,000, and has a lifetime of 20 years.


Therefore we can say that over the three years, the compressor has cost the process a difference of $750, which can be taken out of the taxable income.

Time Value of Money

Money that is available now is inherently more valuable than the same amount in the future, because that money could be used as capital for an investment that earns interest.

Capital that is available in the future is said to be "discounted". The present value of money, which is discussed in further detail in the coming sections, is a discounted amount of the future value:


.


The discount factor, which takes into account an estimated interest rate gained on present money, is calculated for every year :


.


This implies that the a given amount of money in the future has less value as the length of future time increases, and as the expected amount of interest that current capital could gain increases. See Net Present Value for more information on this subject.

Of additional interest is the different between the time value of money and inflation. It is important to note that these two concepts are completely different. Inflation is the yearly rate at which the price of a certain good will increase (Biegler, 169). Although the mathematics and calculations are similar, inflation is generally a result of socioeconomic factors increasing the supply of money, and not the potential interest rate gained on current capital.

Discounted Cash Flow Methods

As discussed above, the value of money is directly related to time, insofar as $500 today is worth more than $500 in two years. Discounted cash flow methods, such as net present value (NPV) and internal rate of return (IRR) take the time value of money into account. The main difference between nondiscounted and discounted cash flows is that all cash flows are related to time zero in the latter.(Turton 266).

Net Present Value

Net Present Value (NPV), also known as Net Present Worth (NPW), gives the present value of all payments and provides a basis of comparison for projects with different payment schedules but similar lifetimes. (Biegler 151). In making comparisons between projects, the larger the net present worth, the more favorable the investment. (Peters 328). It is one of the most widely used economic measures because it captures the time value of money, the value of investment incentives and variations in construction schedule, while allowing for price forecast models that include cyclic behavior. The NPV can be represented as:

where = cash flow in year n and = project lifetime and i is the discount rate as a decimal. (Towler 407). If the net present value is equal to zero, the return of the project is equal to the return that the discount rate would provide. (Peters 328). There are several drawbacks to NPV; it does not measure bang for buck, and it cannot be optimized unless an upper bound is set to the plant size.

Discounted Cash Flow Rate of Return

The DCFROR is the interest or discount rate for which the NPV is equal to zero. (Turton 270). This means that DCFROR represents the highest after tax interest rate at which the project can break even. Often, corporation management will set an "internal" interest rate, which is the lowest rate of return that a company will accept for any new investment. If the DCFROR is greater than this internal rate, the investment is favorable. NPV and DCFROR are almost always used together. (Peters 328). The DCFROR can be represented as:

where i' is the DCFROR. DCFROR is useful for comparing projects of different sizes and for comparing projects to other investments. (Towler 408).

Discounted Payback Period

DPP is the time required, after start-up, to recover the fixed capital costs required for a project with all cash flows discount back to time zero. (Turton 268). The project with the shortest discounted payback period is the most desirable.

Annualized Costs

Annualized Cost is another way of comparing capital expenses with future cash flows where the capital expense is converted into a recurring annual capital charge. It is useful for comparing the cost of assets with different lifetimes. (Towler 411). This is very similar to the way that mortgages are amortized over a 15 or 30 year lifetime. Annual payment can be represented as:

where P is the principle investment, n is investment period, and i is the discount rate. The annual capital charge ratio can be defined as:

It is the fraction of the principle that must be paid each year to recover the investment at the target interest rate.