Title: Pressure Vessels
Author: David Chen
Steward: Fengqi You
Date Presented: January 13, 2014 /Date Revised: January 14, 2014
Codes for pressure vessels can be found in the ASME Boiler and Pressure Vessel Code (ASME BPV code). While there is no formal definition, generally any closed vessel over 150 mm in diameter and that will experience a pressure difference of greater than 0.5 bar can be classified as pressure vessels. Types of equipment that can fit these descriptions include many reactors, separation columns, flash drums, heat exchangers, surge tanks, and storage vessels. Pressure vessels with a wall-thickness:diameter ratio of less than 1:10 can be classified as thin-walled, and the rest, thick-walled.(Towler) Pressure vessels typically consist of a cylindrical shell and elliptical or hemispherical heads at the ends (Peters). Generally, chemical engineers will not be directly involved in detailed mechanical design of pressure vessels. This will be handled by mechanical engineers with experience in the field. However, chemical engineers will need to understand basic concepts of pressure vessel design in order to estimate costs and communicate specifications to those who will carry out the design. Most correlations for estimating cost depend heavily on the weight and type of material used. (Peter/ Towler / Towler/UOP).
Basic data required by pressure vessel design engineer. It will be important for chemical engineer and vessel design engineer to communicate very closely(Towler pg 1-2).:
1. Vessel function
2. Process materials and services (corrosion, deposits, etc.)
3. Operating conditions (temperature and pressure)
4. Materials of construction
5. Dimensions and orientation
6. Type of vessel heads to be used
7. Openings and connections required
8. Heating/cooling requirements
9. Agitation requirements
10. Specification of internal fittings
Designs and Codes
Many countries have codes and standards concerning pressure vessels. Compliance is usually legally required. The codes provide guidance on design, materials of construction, fabrication, inspection, and testing. In North America, the American Society of Mechanical Engineers Boiler and Pressure Vessel Code (ASME BPV Code) is used. There are twelve sections, and section VIII has three subdivisions. The section titles are listed below. Other sets of codes exist for storage tanks, fittings, and piping. It is important to always use the most recent revisions in design. (Towler 3-5)
TABLE "American Society of Mechanical Engineers Boiler and Pressure Vessel Design Codes"
I Rules for construction of power boilers
III Nuclear power plant components
IV Rules for construction of heating boilers
V Nondestructive examination
VI Recommended rules for the care and operation of heating boilers
VII Recommended guidelines for the care of power boilers
VIII Rules for the construction of pressure vessels
VIII. D2 Alternative rules
VIII. D3 Alternative rules for the construction of high pressure vessels
IX Welding and brazing qualifications
X Fiber-reinforced plastic vessels
XI Rules for in service inspection of nuclear power plant components
XII Rules for construction and continued service of transport tanks
Different temperature allowances are used above and below normal operating tempratures. For temperatures between -30 and 345 ⁰C, Turton gives a maximum allowance of 25 ⁰C above maximum operating temperature should be included. Above this, an even higher design allowance is used (Turton pg 1). Towler/UOP gives 50 ⁰F above the maximum operating temperature and -25 ⁰F below the minimum. (Towler/UOP)
Maximum allowable stress is highly dependent on temperature, because metals weaken with increasing temperature. The vessel should not operate at higher temperature than the highest at which the maximum allowable stress was evaluated.
There is also a minimum temperature for which the vessel can be guaranteed to operate safely. Metals may become brittle at very low temperatures (Towler/UOP).The minimum design metla temperaure (MDMT) is the lowest temperature that can be expected in the vessel. (Towler)
In specifying the maximum and minimum temperatures, disturbances caused by upstream processes and external factors need to be taken into account. These disturbances may include:transient conditions, upsets, auto-refrigeration, climate, other cooling factors. (Towler pg 8-9, Towler/UOP)
Vessels are often overdesigned relative to the maximum operating pressure. Turton suggests deisgn pressures of either 10% or 0.69-1/7 bar above the maximum operating pressure, whichever is greater. The maximum operating pressure is taken a 1.7 bar above normal operation. for example, the design pressure of a vessel that normall operates at 0-0.69 bar and 95-540 ⁰C is 2.76 barg. (Turton pg 1). Towler suggests overdesign of vessel pressures by 5-10%.
For vessels that will experience external pressure, design pressure is based on the maximum difference between internal and external pressure.
Vessels that may potentially experience vacuum conditions must be designed to resist a negative pressure of one full atmosphere. Because of the large surface areas of some vessels, even a modest vacuum can lead to collapse. Circumstances that may lead to vacuum conditions include: startup/shutdown procedures, cooling vessels with condensable vapors, pumping or draining without proper venting, or some other unexpected disturbance. (Towler 7-9 / Towler UOP).
Maximum Allowable Stress
The maximum allowable stress is obtained by applying a safety factor to the maximum stress that the material can withstand under standard testing conditions. This allows for possible deviations from ideal material properties and ideal vessel construction.
The ASME BPV Code Section II Part D, Mandatory Appendix 1 details methods on obtaining maximum allowable stress. It is different depending on whether creep and stress rupture are dominant among the various stresses that are present.
Steel is the most common material used in construction of tanks and pressure vessels. Other construction materials include other alloys, wood, concrete, or fiber-reinforced plastics (some low-pressure applications).
Materials must be chosen that will be able to resist deformation and failure at the process temperature and pressure, and be compatible with the internal material. (Peters, pg 552/ Towler pg 8-9/ Towler/UOP) Other factors for selection include ease of fabrication, availability of parts, and cost. (Towler/UOP)
The required wall thickness of a vessel will depend on many factors, including: the strength of the metal at operating conditions (temperature and pressure), diameter of the tank, and the joint efficiencies. According to Peters, in "Plant Design and Economics for Chemical Engineers," minimum wall thickness, not including corrosion allowances, should not be less than 2.4mm for welded or brazed construction and 4.8mm for riveted construction. Thickness for unfired steam boilers should not be less than 6.35 mm. (Peters 552) Turton gives heuristics for wall thickness for rigidity based on vessel diameter: 4 mm (0.25 in) for 1.07 m (42 in) diameter and less than 8.1mm (0.32 in) for 1.07-1.52 m (42-60 in) diameter, and 11.7 mm (0.38 mm) for more than 1.52 m (60 in) diameter (Turton).
ASME BPV Code Section VIII D.1 states that wall thickness should always be at least 1/16 in, not considering corrosion allowance, material, or dimensions.
Minimum wall thicknesses do not include corrosion allowances. (11-13)
In general, corrosion allowances will range from 1.5-5mm. Corrosion allowances for heat transfer equipment are smaller, because wall thickness has an important effect on heat transfer. (Towler/UOP)
Corrosion and erosion will lead to eventual thinning of walls, which compromises mechanical integrity. Corrosion allowance is constructing the vessels with thicker walls to allow for the thinning. the Peters, Timmerhaus, and West suggest 0.25 to 0.38mm annually or 3mm for 10 years.
Turton et al. suggest a corrosion allowance 8.9 mm (0.35 in) for known corrosive conditions, 3.8 mm (0.15 in) for noncorrosive streams, and 1.5 mm (0.6 in) for stream drums and air receivers.
In cases where corrosion is negligible over the lifetime of a vessel or does not occur, the vessel can be designed without the corrosion allowance. (Towler pg 11)
Most pressure vessels are cylindrical (swaged vessels are an exception) and have integer length:diameter ratios (2:1, 3:1, 4:1). Vertical vessels are more commonly used than horizontal ones. This is because it is easier to have uniform distribution across the cross section, and they take up less space. However, there may be cases in which horizontal vessels may be preferable. They can be used to promote phase separation (in decanters, settling tanks, separators, and flash vessels), and to allow easy access to clean the inside (in heat exchangers).
In general, vessel shells are made by rolling and welding. It is easier for thin walls, however there may still be difficulty for small diameters. Vessels with thicker walls may need to be drum forged. The end closures are usually forged, and auxiliary components such as nozzles and support rings are welded on. Post weld heat treating (PWHT) is used to relieve residual stresses caused by forming and joining.
The heads on the ends of the vessels can be hemispherical, ellipsoidal, or torispherical. Hemispherical heads have greater internal volumes than ellipsoidal heads, which have greater internal volumes than torispherical heads. The internal volumes are correlated with the cost of each type of head. Tangent and weld lines usually are not the same. Tangent lines are where the curvature ends. Weld lines are where the closures are attached. Different kinds of welds can be used. ASME BPV Code has guidelines concerning weld types and inspection.
Gasketed joints can be used then vessels need to be frequently opened, and for instrument connections. However, they are not used at high temperature or pressures because they may fail, and welds are stronger. They are also more prone to leaks than welded joints. (Towler/UOP)
The ASME BPV Code Section VIII D.1 defines four kinds of welds and criteria for their evaluation(Towler pg 10-11).
A. Longitudinal or spiral welds in the main shell, necks, or nozzles, or circumferential welds connecting hemispherical head sto the main shell, necks or nozzles
B. Circumferential welds int he main shell, necks, or nozzles or connecting a formed head other than hemispherical
C. Welds connecting flanges, tubesheets, or flat heads to the main shell, a formed head, neck or nozzle
D. Welds connecting communicating
High Pressure Vessels
High pressures are often required to carry out chemical processes. Section VIII Division 2 of the ASME BPV Code provides guidelines for pressure vessels that will experience pressures above 2000 psia. There are stricter restrictions and requirements regarding operating temperatures and stress analysis and testing. Divison 3 of Section 8 provides guidelines for pressures above 10,000 psia (680 bar).
At high pressures, compound vessels are often used instead of single-walled vessels, which may have difficulty providing the necessary strength. (Towler 56-57)
One way of creating compound vessels is to use multiple cylinders such that the outer diameter of the inner cylinder is larger than the inner diameter of the outer one. The outer cylinder can be expanded by heating, and compresses the inner cylinder when cooled. Multiple cylinders may be used.
Multilayer cylinders are made by wrapping thin plates around a tube in layers. They are heated, tightened, and welded.
Wound vessels are cylindrical vessels reinforced by winding on wire or thin ribbons under tension. The strips can be interlocked to provide more strength for high-pressure applications.
The internal surface of the vessel is subject to enormous pressures to prestress it. When released, the inside will be under compression by the outside. The vessel can be used up to the “autofrettage” pressure without further deformation.
Liquid Storage Tanks
Vertical cylindrical tanks are common in industry for storage of liquid. Volumes can range from a few hundred to several thousand gallons. The main load for these tanks is the hydrostatic head. However, tanks with large vertical profiles may need to account for wind loading, and perhaps snow on the top as well.
Nondestructive testing methods are ways of evaluating the integrity of a vessel without compromising it. Inspections need to be carried out for new vessels and regularly once operation begins.
The simplest is a visual inspection for cracks or defects on the surface. It is also the cheapest, requiring only an inspector.
Radiography is used to detect subsurface cracks and defects. It is difficult and expensive, and may require specialized inspectors. It is required by the code in certain cases.
Ultrasonic detection can be used during operation to detect wall thinning.
The ASME BPV Code requires pressure testing with an inspector present before vessels can be approved.
Both hydraulic and pneumatic pressure tests are used. Hydraulic testing is preferred to pneumatic for safety reasons because much less energy is stored in compressed liquid than in compressed gas (Towler, Towler/UOP)
The equation below is typically used to determine an appropriate test pressure (Towler pg 56).
= design pressure, N/mm^2
= maximum allowable stress at test temperature, N/mm^2
=maximum allowable stress at the design temperature, N/mm^2
= corrosion allowance, mm
= actual plate thickness, mm
Adjustments are made for the testing and design temperature. If the thickness cannot be calculated using known methods, a hydraulic proof test is required by the ASME BPV Code. (Towler)
Stress cycles can occur as a result of normal operations. Possible periodic causes include:
1. Fluctuations in pressure
2. Temperature cycling
4. Water hammer
5. Fluctuations in flow of fluids or solids
6. Fluctuations in external load
The endurance limit is the number of cycles for failure at a given set of conditions of cyclic stress. If this number of cycles is exceeded, the vessel will fail (Towler pg 55).