Process flow diagram: Difference between revisions

From processdesign
Jump to navigation Jump to search
No edit summary
No edit summary
Line 27: Line 27:
#Mean values for stream
#Mean values for stream
#Stream names
#Stream names

===Categorization of Information In a Process Flow Diagram===
The information that a process flow diagram conveys can be categorized into one of the following three groups:
*Process topology
*Stream information
*Equipment information

==Process Topology==
Process topology is defined as the interactions and locations of the different equipment and streams. It includes all of the connections between the equipment and how one stream is changed to another after it flows through a piece of equipment. It should be noted on a separate table following the PFD, the equipment on the must be labeled (it can be labeled with a number) and followed by a short description so that the engineer who is trying to understand the PFD will have a easier time following along.

===Naming Equipment===
Typical names for the equipment include a letter followed by a set of numbers. The letter usually corresponds to the first letter of the equipment. For example, the first pump in the PFD is typically labeled P-101. The following table displays the convention of naming the letters for process equipment:
*C-Compressor or Turbine
*E-Heat Exchanger
*H-Fired Heater
*P-Pump
*R-Reactor
*T-Tower
*TK-Storage Tank
*V-Vessel
*Y means that it is a specific area in the plant
*A/B identifies parallel units or backup units not shown on a PFD

Additionally, it should be noted that in a plant, certain equipment will need to be replaced. Typically, the new equipment will take the old equipment's name but an additional letter or number will be added onto the new equipment to indicate that there was a modification.
===Symbols for Process Technology===
For process equipment, there are a few standard symbols that should be recognized by chemical engineers. These symbols are displayed in the following figure:

Revision as of 22:53, 5 February 2015


Author: Tammy Wong [2015]

Stewards: Jian Gong and Fengqi You


Introduction

The process flow diagram (PFD) is a critical component of process design. It is absolutely necessary that chemical engineers know how to read process flow diagrams because it is the primary method of detailing the process and design information. Additionally, the most effective way of relaying information about a process design is the use of process flow diagrams. The PFD shows the sequence of flow through a system through the various equipment (such as piping, instrumentation, and equipment design) and details the stream connections, stream flow rates and compositions and operating conditions through the plant layout. The PFD differs from a block flow diagram (BFD) in that the PFD is more detailed and conveys more information than the BFD, which only gives a general sense of flow of information.

Overview

Essential Information That Must Be Included In A Process Flow Diagram

  1. Process vessels and equipment (such as heat exchangers, pumps, distillation columns, and reactors)
  2. Process piping
  3. Process and Utility Flow Lines
  4. Full heat and material balances
  5. Composition, flow rate, pressure and temperature of every stream
  6. Stream enthalpy
  7. Location of every control valve
  8. Sizing of pumps and compressors
  9. Bypass and recycle streams

Optional Information That Can Be incorporated In A Process Flow Diagram

  1. Molar percentage composition and/or molar flow rates
  2. Physical property data
  3. Mean values for stream
  4. Stream names

Categorization of Information In a Process Flow Diagram

The information that a process flow diagram conveys can be categorized into one of the following three groups:

  • Process topology
  • Stream information
  • Equipment information

Process Topology

Process topology is defined as the interactions and locations of the different equipment and streams. It includes all of the connections between the equipment and how one stream is changed to another after it flows through a piece of equipment. It should be noted on a separate table following the PFD, the equipment on the must be labeled (it can be labeled with a number) and followed by a short description so that the engineer who is trying to understand the PFD will have a easier time following along.

Naming Equipment

Typical names for the equipment include a letter followed by a set of numbers. The letter usually corresponds to the first letter of the equipment. For example, the first pump in the PFD is typically labeled P-101. The following table displays the convention of naming the letters for process equipment:

  • C-Compressor or Turbine
  • E-Heat Exchanger
  • H-Fired Heater
  • P-Pump
  • R-Reactor
  • T-Tower
  • TK-Storage Tank
  • V-Vessel
  • Y means that it is a specific area in the plant
  • A/B identifies parallel units or backup units not shown on a PFD

Additionally, it should be noted that in a plant, certain equipment will need to be replaced. Typically, the new equipment will take the old equipment's name but an additional letter or number will be added onto the new equipment to indicate that there was a modification.


Symbols for Process Technology

For process equipment, there are a few standard symbols that should be recognized by chemical engineers. These symbols are displayed in the following figure: