Reactors

From processdesign
Jump to navigation Jump to search


Title: Reactors

Author: Sean Cabaniss, David Park, Maxim Slivinsky and Julianne Wagoner

Steward: Fengqi You

Date Presented: February 4, 2014 /Date Revised: February 4, 2014


Introduction

Ideal Reactors

Batch Reactors

Plug Flow Reactor (PFR)

A PFR with tubular geometry has perfect radial mixing but no axial mixing. All materials hav the same residence time, τ, and experience the same temperature and concentration profiles along the reactor. Equation for PFR is given by:

where M = molar flow rate, dV is the incremental volume, and R is the rate of reaction per unit volume.

This equation can be integrated along the length of the reactor to yield relationships between reactor resident time and concentration or conversion.

Continuously Stirred Tank Reactor (CSTR)

In a CSTR there is no spatial variation- the entire vessel contents is at the same temperature, pressure, and concentration. Therefore the fluid leaving the reactor is at the same temperature and concentration as the fluid inside the reactor.

The material balance across the CSTR is given by:

General Reactor Design

The design of the reactor should not be carried out separately from the overall process design due to the significant impact on capital and operating costs on other parts of the process[1].

Collect Required Data

Out of all process equipment, reactor design requires the most process input data: reaction enthalpies, phase-equilibrium constants, heat and mass transfer coefficients, as well as reaction rate constants. All of the aforementioned parameters can be estimated using simulation models or literature correlations except for reaction rate constant constants, which need to be determined experimentally.

Enthalpy of Reaction

The heat given out in a chemical reaction is based on the enthalpies of the component chemical reactions, which are given for standard temperature and pressure (1 atm, 25 C).

Equilibrium Constant and Gibbs Free Energy

Reaction Mechanisms, Rate Equations, and Rate Constants

Heat and Mass Transfer Properties

Select Reaction Conditions

Chemical or Biochemical Reaction

Catalyst

Temperature

Pressure

Reaction Phase

Solvent

Concentrations

Determine Materials of Construction

Determine Rate-Limiting Step and Critical Sizing Parameters

The key parameters that determine the extent of reaction must be identified by carrying out an experiment plan with a broad range of conditions. In general, the rate of reaction is usually limited by the following fundamental processes. The first three have been discussed in previous sections. Mixing will be developed in more detail in its own section.

  • Intrinsic kinetics: There will usually be one slowest step that governs the overall rate.
  • Mass-transfer rate: In multiphase reactions and processes that use porous heterogeneous catalysis, mass transfer can be particularly important. Often, careful experimentation will be needed to separate the effects of mass transfer and the rate of reaction to determine which is the rate-limiting step.
  • Heat-transfer rate: The rate of heat addition can become the governing parameter for endothermic reactions. Heat-transfer devices such as heat exchangers or fired heaters may need to be used.
  • Mixing: The time taken to mix the reagents can be the limiting step for very fast reactions.

Once rate data have been collected, the designer can fit a suitable model of reaction kinetics. Next, a critical sizing parameter can be specified for the reactor. This will usually be one of the parameters given in Figure 1.

Sizing Parameters.PNG

Figure 1. Reactor Sizing Parameters [1]

Preliminary Sizing, Layout, and Costing of Reactor

Estimate the Performance

Optimize the Design

Mixing in Industrial Reactors

Mixing plays an important role in many processing stages, including reactor performance. It is critical to select the appropriate method of mixing in order to ensure the process is effective and cost efficient.

Gas Mixing

Gases mix easily because of their low viscosities. The mixing given by turbulent flow in a length of pipe is usually sufficient for most purposes [1]. Orifices, vanes, and baffles can be used to increase turbulence.

Liquid Mixing

  • Inline Mixing Inline mixers can be used for the continuous mixing of low-viscosity fluids. One inexpensive method involves the use of static devices that promote turbulent mixing in pipelines. Some typical designs are shown in Figures 2(a), (b), and (c).
Static Mixers.PNG

Heating and Cooling of Reacting Systems

Types of Reactors

Types of Reactors.PNG

Multiphase Reactors

Catalytic Processes

Bioreactors

Safety Considerations in Reactor Design

Capital Cost of Reactors

Conclusions

References

  1. Towler, G.P. and Sinnot, R. (2012). Chemical Engineering Design: Principles, Practice and Economics of Plant and Process Design.Elsevier.